This has a processor controlling the voltage regulation. If the voltage changes outside of the "safe" window, 190V low or 270V high, then the HLVD shutsdown the power. The internal processor clock then monitors the voltage and when the voltage returns within the "safe" window it waits 3 minutes before re-activating the power automatically. Thus making sure the connected equipment only ever receives safe power. If the voltage travels outside the "safe" window while the timer is on then the timer re-sets.
Note: Factory delay 180 seconds/3minutes can be adjusted donw to a few seconds if shorter delay required. When power voltage fluctuates electrical equipment suffers. The HLVD is designed to automatically detect a problem then offer shutdown protection until the danger subsides. Once the voltage returns to a safe level then the HLVD automatically re-activtes power to the circuit. The protection is against both high and low voltage incidents.The HLVD has an inbuilt factory delay of 3 minutes this is primarily because it is designed to protect electric motors, refrigeration and air-conditioing compressors from burning out or blowing up. If a compressor is under load and the power is turned on/off quickly this action can cause a compressor irrepairable damage. If an electric motor is supplied low voltage for a period of time this type of supply can cause the motor to burn out.
The HLVD will allow power to pass through as long as the voltage supply is above 190V (low) or below 270V (high). Should the voltage move out of the predefined “safe” window then the HLVD reacts by offering shutdown protection and cutting supply until the voltage supply returns to the “safe” level. If the power moves in and out of the “safe” level then each incident resets the on board clock count down to reactivation, this feature prevents damage occuring when voltage is unstable or erratic.
The delay can be reduced down to seconds or increased if need be. An example of reducing the delay could be applied to applications where equipment is not pressurised or does not require any lenghty delay. An example would be a lighting circuit, in this example the lights may become damaged if there is too much voltage going through and the HLVD would be a great option to protect the circuit. Other applications may be control equipment or PLC’s, printing presses, commercial kitchen equipment, office printers, photocopiers, dishwashers, fridges, freezers, dryers etc.
Features:
Processor controlled
LED ALERT:Orange/delay mode
LED ALERT: Slow red/ surge
LED ALERT:Fast red/ voltage dip
Manufactured in Australia
6 Year replacement warranty
Protects:
Whole circuit protection
Air-conditioners
Motor/pump burn out protection
Shutdown protection (auto re-start)
Compressors
Product Specifications:
Product Dimensions: 70mm x 90mm x 60mm
Supply voltage 240/V AC 50Hz
Maximum current rating 20amps/4800 W (VA)
Reaction Speed 800 m/secs
Detection Voltage 190V to 270V
Delay 180 seconds (3 minutes)
LED combination Green = Ok, Orange = Delay mode
LED combination Red (slow flash) = High Voltage detected, RED (fast flash) = Low Voltage detected
Reset Delay override (push button on front)
Operating Temperature -10C/+60C
Housing High Temperature impact Polycarbonate Housing Din Rail Mount
High/Low Voltage Range
Delay
Reaction Speed
This has a processor controlling the voltage regulation. If the voltage changes outside of the "safe" window, 190V low or 270V high, then the HLVD shutsdown the power. The internal processor clock then monitors the voltage and when the voltage returns within the "safe" window it waits 3 minutes before re-activating the power automatically. Thus making sure the connected equipment only ever receives safe power. If the voltage travels outside the "safe" window while the timer is on then the timer re-sets.
Note: Factory delay 180 seconds/3minutes can be adjusted donw to a few seconds if shorter delay required.
When power voltage fluctuates electrical equipment suffers. The HLVD is designed to automatically detect a problem then offer shutdown protection until the danger subsides. Once the voltage returns to a safe level then the HLVD automatically re-activtes power to the circuit. The protection is against both high and low voltage incidents.The HLVD has an inbuilt factory delay of 3 minutes this is primarily because it is designed to protect electric motors, refrigeration and air-conditioing compressors from burning out or blowing up. If a compressor is under load and the power is turned on/off quickly this action can cause a compressor irrepairable damage. If an electric motor is supplied low voltage for a period of time this type of supply can cause the motor to burn out.
The HLVD will allow power to pass through as long as the voltage supply is above 190V (low) or below 270V (high). Should the voltage move out of the predefined “safe” window then the HLVD reacts by offering shutdown protection and cutting supply until the voltage supply returns to the “safe” level. If the power moves in and out of the “safe” level then each incident resets the on board clock count down to reactivation, this feature prevents damage occuring when voltage is unstable or erratic.
The delay can be reduced down to seconds or increased if need be. An example of reducing the delay could be applied to applications where equipment is not pressurised or does not require any lenghty delay. An example would be a lighting circuit, in this example the lights may become damaged if there is too much voltage going through and the HLVD would be a great option to protect the circuit. Other applications may be control equipment or PLC’s, printing presses, commercial kitchen equipment, office printers, photocopiers, dishwashers, fridges, freezers, dryers etc.
Features:
Protects:
Product Specifications: